,cnc machinist,cnc manufacturing,cnc mechanic,cnc mill,cnc milling center,cnc milling companies,cnc milling tools,cnc parts,cnc plasma cutter,cnc plasma cutting,cnc plasma table,cnc production,cnc router table,cnc screw machine,cnc service,cnc swiss,cnc turning,cnc turning center,cnc turning centers,cnc vertical lathe,horizontal cnc,how to cnc machine,machining cnc,manufacturing cnc machines,okuma cnc,plasma cnc machine,production cnc machining,troubleshooting cnc machines,used cnc machine tools,used cnc milling machines,vertical cnc lathe,what can a cnc machine make
Below are the fabrication details of a sleigh bed I designed and built for the Wolff family. The bed is made of Cherry and Tiger Maple.
First a word of thanks - especially to Rodger and Patti Wolff who were fantastic clients. Also to everyone at Taubman College who were so helpful to me - Wes McGee, Maciej Kaczynski, and Ben Hagenhofer-Daniell. And a special thanks to my good friend, Bob Ongaro who was enormously helpful through the entire process!
The Wolff's wanted a clean design where the wood was the main feature. They also wanted to use two contrasting woods. We looked at a lot of different combinations before choosing Cherry and Maple. Here's the original computer model after several design iterations.
The blank is secured to a 4'x8' sheet of plywood and placed on the 3-axis CNC router table.
Various cutters carve out the form. Here you can see the initial roughing done by a 1/2" wide straight cutting bit. This remove the bulk of the material.
Next a 1" diameter ball bit makes passes over the surface to smooth it out. Each pass steps over 0.07" from the previous pass.
The machine goes around and around until the entire surface has been smoothed.
A side fully routed. A small chamfer was added with a hand held router on the back side to soften the edge. That was inaccessible to a 3-axis CNC. The large chamfer on the outer face was cut by the CNC.
Here the router does a similar job as was done to the sides. First the blank is roughed then a ball bit it smooths the surface.
Here's the fixture after have been smoothed.
Next a grid is cut to distribute vacuum pressure over the entire face of the blank.
This is the fixture for cutting the convex side. Holes are drill through the entire fixture to allow the vacuum pressure to come from the table below and into the grid.
A rubber gasket is inserted into the outer groove. This prevents the vacuum pressure from escaping. Also, paint is used to seal the edges of the fixture - again to ensure the vacuum is only applied to the part.
Next the flat pieces of 6/4 Maple are glued up, edge to edge, in the same way a barrel is made. Below the individual boards have been cut on the table saw to the appropriate angle and jointed. Here they are shown before before any clamp pressure is applied.
Finally the headboard is trimmed on its edges. These sit flush against the side pieces.
Here's the footboard being milled. The shape has been cut and the ball bit is smoothing the surface.
The finished piece.
This results in a lot of shavings. On top the Cherry, below it the Maple.
Here are the pieces during scraping and sanding.Eventually the parts were sanded to 400 grit between coats of finish.
Here's it is in action. Steel is no match for water and garnet abrasive under intense pressure.
Here's the finished part. The missing piece in the upper right was removed during the cutting to test the fit - it is one of the hooks and slides into the grooves cut into each piece.
These then need to be released from the blank and countersunk so screws will be recessed. The hooks then get welded into the plates.
The hardware is recessed into the headboard and footboard sides using a Dremel tool with a teeeeeny router bit and router base. The corners are cleaned up with a skew chisel.
All done while standing on a step ladder to reach the edges and to work horizontally. (In the background of the picture you can see the Fab Lab's 7-axis robot).
Here you can see the hooks of the plates. These latch into matching plates mortised into the sides. Note that the angle of the hooks have to be perfectly vertical in the final orientation in the bed. Otherwise the parts would not be able to slide together.
And set up in the Wolff bedroom.
